ราคาดี  ออนไลน์

รายละเอียดสินค้า

บ้าน > ผลิตภัณฑ์ >
High Temperature EDI Module
>
EIMD-20CP High Temp EDI Module Water Purification Condensate Polishing Module

EIMD-20CP High Temp EDI Module Water Purification Condensate Polishing Module

ชื่อแบรนด์: Aquacells
เลขรุ่น: EIMD-20CP
ข้อมูลรายละเอียด
สถานที่กำเนิด:
จีน
ได้รับการรับรอง:
FDA,EU,CE,RoHS,REACH
อัตราการปฏิเสธเกลือ:
มากกว่า 99%
ระยะเวลาการรับประกัน:
12 เดือน
แหล่งจ่ายไฟ:
220 V/50 Hz
ขนาด:
500 มม. x 300 มม. x 200 มม.
แอปพลิเคชัน:
การทำน้ำให้บริสุทธิ์ด้วยอุณหภูมิสูงในกระบวนการทางอุตสาหกรรม
ช่วงการทำงานของพีเอช:
2 ถึง 11
วัสดุ:
อิเล็กโทรดโพลีเมอร์และไทเทเนียมคุณภาพสูง
ชื่อสินค้า:
โมดูล EDI อุณหภูมิสูง
น้ำหนัก:
15 กก
ช่วงเวลาการบำรุงรักษา:
ทุก 6 เดือน
อัตราการไหล:
0.5 ถึง 3.0 ลบ.ม./ชม
ช่วงอุณหภูมิในการทำงาน:
สูงถึง 95°C
การกำจัดการนำไฟฟ้า:
มากถึง 99%
แรงดันสูงสุด:
6 บาร์
อัตราการกู้คืนน้ำ:
มากถึง 85%
เน้น:

High Temp EDI Module

,

EDI Module Condensate Polishing

,

EDI Water Purification Condensate Polishing

คําอธิบายสินค้า
EIMD-20CP Condensate Polishing Module With 16 MΩ*Cm Resistivity And 90-95% Recovery Using Continuous Electrodeionization

The Aquacells EIMD-CP module is engineered to replace mixed bed technology for condensate polishing treatment. Utilizing continuous electrodeionization (EDI) technology, this system produces water with resistivity exceeding 16 MΩ*cm without requiring shutdown and regeneration cycles.

Feed Water Specifications
Parameter Specification
Feed Water Source Condensate water
Temperature 60-65 ℃ (60-65 ℉)
Feed Pressure 1.4-7 bar (20-100 psi)
Fe Content <0.01 ppm
pH Range 4-11
Oil Content <0.2 ppm
Typical Module Performance
Parameter Specification
Typical Recovery 90-95%
Maximum Feed Pressure 7 bar (100 psi)
Maximum Feed Temperature 65 ℃ (149 ℉)
DC Voltage* 0-300 V
DC Amperage 0-6 A
Product Resistivity >16 MΩ·cm
*Voltage required depends on module size
*The information provided contains general descriptions or performance characteristics that may not always apply as described in actual use cases or may change due to further product development. An obligation to provide the respective characteristics shall only exist if expressly agreed upon in the terms of the contract.
สินค้าที่เกี่ยวข้อง